916253
Unfortunately, this car part is unavailable. If you enter your email address or phone number, we will notify you as soon as it is back in stock.
Top spare parts products
incl. 20% VAT, free delivery
- Product line: RepSet DMF
- Supplementary Article / Supplementary Info Info 2: with flywheel, with screw set, Requires special tools for mounting, Dual-mass flywheel with friction control plate
- Supplementary Article / Supplementary Info: with central slave cylinder, without pilot bearing
- Adjustment: with automatic adjustment
- Number of teeth (finding the max. clearance angle): 7
- max. side clearance [mm]: 2,9
- Max. Clearance Angle [Degree]: 18
- Number of mounting bores: 6
- Condition: New
Over 100 in stock
incl. 20% VAT, excl. delivery costs
- Fitting Position: Front Axle
- Supplementary Article / Supplementary Info: with fastening/mounting material
- Supplementary Article / Supplementary Info Info 2: with axle joint, with rubber mount, with coupling rod, with ball joint
- Control/Trailing Arm Type: Control Arm
- Steering: with tie rod ends
- Quantity per axle: 1
- Full Set
- for components see parts list
- Axle alignment required after fitting
- Supplementary Info: t+
- Condition: New
Over 100 in stock
incl. 20% VAT, excl. delivery costs
- Product line: B4 OE Replacement
- Fitting Position: Rear Axle
- Shock Absorber System: Twin-Tube
- Shock Absorber Type: Gas Pressure
- Shock Absorber Design: Absorber does not carry a spring
- Shock Absorber Mounting Type: Bottom eye, Top pin
- Condition: New
Over 100 in stock

incl. 20% VAT, excl. delivery costs
- Fitting Position: Front Axle, Right, Left, Front Axle Right, Front Axle Left
- Shock Absorber Type: Gas Pressure
- Shock Absorber System: Twin-Tube
- Shock Absorber Design: Suspension Strut, Damper Module
- Mounting Type: Pre-assembled
- Replace in pairs only
- Supplementary Article / Supplementary Info Info 2: with bolts/screws
- Condition: New
Over 100 in stock
incl. 20% VAT, free delivery
- Product line: KIT4P - CONVERSION KIT
- Number of Teeth: 28
- Supplementary Article / Supplementary Info Info 2: with screw set, with lock screw set, with clutch release bearing, Requires special tools for mounting
- Supplementary Article / Supplementary Info: with single-mass flywheel
- New Part
- Hub Profile: 22,1 x 20,3
- Weight [kg]: 15,02
- Clutch: Conversion from dual-mass flywheel to single-mass flywheel, for vehicles with push type clutch
- for flywheel manufacturer: LUK
- Tightening Torque [Nm]: 60
- Tightening angle [degrees]: 90
- Clutch Pressure Plate Outer Diameter [mm]: 228
- Condition: New
Over 100 in stock

incl. 20% VAT, excl. delivery costs
- Fitting Position: Front Axle Left, Lower, Front Axle Right
- Material: Sheet Steel
- Control/Trailing Arm Type: Control Arm
- Supplementary Article / Supplementary Info Info 2: without ball joint
- Weight [kg]: 2,456
- Supplementary Article / Supplementary Info: with rubber mounts
- Observe service information
- Condition: New
Over 100 in stock
incl. 20% VAT, excl. delivery costs
- Oil Viscosity Classification SAE: 5W-30
- Capacity [litre]: 10
- Oil: Part Synthetic Oil
- Specification: API CH-4, ACEA A3/B4, API SN
- Manufacturer recommendations: Ford WSS-M2C913-B, VW 502 00, VW 505 00, MB 229.3, VW 503 01, VW 501 01, MB 229.5, BMW Longlife-98, Renault RN0710, Renault RN0700
- Product line: ENERGY
Over 100 in stock

incl. 20% VAT, excl. delivery costs
- Oil Viscosity Classification SAE: 0W-40
- Capacity [litre]: 4
- Specification: API SN, API CF, ACEA A3/B4
- Manufacturer recommendations: AAE STO 003 B7, MB 229.3, MB 229.5, VW 502 00, VW 503 01, VW 505 00, Porsche A40, Fiat 9.55535-M2, Ford WSS-M2C937-A
- Product line: 1
- Version: FS
- Packing Type: Canister
- Vehicle type: Car
- Condition: New
Over 100 in stock