Search for Shock absorber dust cover & bump stops:
Shock absorber dust cover & bump stops for automobile

- Shock absorber
- Strut mount
- Strut bearing
- Coil springs
- Coil spring seat
- Leaf spring
- Air suspension
Choose your car and find high-quality Bump stops & Shock absorber dust cover
-
MITSUBISHI
- OUTLANDER
- PAJERO / SHOGUN
- LANCER
Information - Shock absorber dust cover & Suspension bump stops
If dust is collected and penetrates the car units, be prepared for function disturbance and wear out augmentation. In order to secure the vehicle components and assemblies from dust, the hydraulic tank mouths of the clutch brakes should be covered with special transparent bags, made from high-quality pellicle.
After that you must fix them with a rubber band. By doing so, you will surely protect the transmission from dust. Some cars are already provided with such protection bags. Mud and dust will certainly not get into the cars systems. When the crankcase ventilation system is running, dust will definitely be absorbed by the engine through the control openings of the oil meter.
In most modern cars these openings are sealed, but the older models are not provided with such items. You can secure this part by using a very simple rubber hose or cap. If you happen to drive on very dusty roads, it is necessary to protect the ignition distributor from dust and dirt. To do this, wrap the distributor in a special dense tissue, collect all the wires together and tie them to a cord. In case you use a plastic bag instead of a tissue for isolating the ignition distributor, moisture will condense in the generator, and will negatively affect the work of the ignition.
If you need to buy a dust protection car set, that will effectively protect the most vulnerable parts of your car from mud and dust, we suggest you do it in our online store. We have all the necessary car parts and accessories only from manufacturers, and we offer you the lowest prices and fast delivery. You also can order any other items for your car - hydraulic filter, steering knuckles or brake pads.
What you need to know about shock absorber dust boots and bump stops replacement: lifetime limits, common defects and their signs, tips and recommendations.
Operational lifetimes of the shock absorber dust boots and bump stops are not limited with a certain period. Their operation duration, first of all, depends on road surface quality. As a rule, a new dust cover kit is installed during shock absorber replacement, however, such necessity may occur earlier. Common defects of the dust boot and bump stop are elasticity loss, deformation, tears and cracking.
Necessity of part replacement can be also indicated by car clearance lowering. Also, damaging of the shock absorber bump stop and dust boot can cause leakage of oil from the shock absorber, that is why you should pay attention to traces of working fluid near the car wheels.
Diagnostics of the parts lies in their visual inspection. Deformation, cracks and punctures point out necessity of dust boots and bump stops of the front or rear shock absorbers replacement.
It is recommended to perform components replacement at a service station, because special tools and skills are necessary for that. Moreover, actions sequence may vary according to car model, type and mounting location of the parts. Generally, procedure of dust boots and bump stops of the front or rear shock struts replacement includes demounting of the wheel and shock strut. Sometimes, disconnection of the brake hose and steering knuckle from the shock strut is required. Then, the spring is compressed with a help of a special removal tool, and the dust boot and bump stop, which became defective, are removed. After this, a new dust boot kit is installed and assembling is performed in the reverse order.
Best goods: Shock absorber dust cover & bump stops

- Fitting Position: Rear Axle
- Condition: New

- Supplementary Info: Protection Kit
- Fitting Position: Rear Axle
- Condition: New
- Fitting Position: Rear Axle
- Material: PU (Polyurethane), Elastomer
- for OE number: 2K5 511 155
- Weight [kg]: 0,02
- Condition: New

- Weight [kg]: 0,400
- Packaging length [cm]: 22
- Packaging width [cm]: 11
- Packaging height [cm]: 18
- Condition: New
- Fitting Position: Rear Axle
- for OE number: 900 064 n.cpl.1
- Condition: New
- Shape: round
- Weight [kg]: 0,400
- Packaging length [cm]: 22
- Packaging width [cm]: 11
- Packaging height [cm]: 18
- Condition: New
- Weight [kg]: 0,300
- Packaging length [cm]: 22
- Packaging width [cm]: 11
- Packaging height [cm]: 18
- Condition: New
- Supplementary Info: Protection Kit
- Fitting Position: Rear Axle
- Condition: New
- Weight [kg]: 0,100
- Packaging length [cm]: 22
- Packaging width [cm]: 11
- Packaging height [cm]: 18
- Condition: New
- Supplementary Info: Service Kit
- Quantity per axle: 1
- Condition: New
- Supplementary Info: Service Kit
- Shape: round
- Condition: New
- Supplementary Info: Service Kit
- Condition: New